CHECK OUT OUR NEWLY DESIGNED ETHERNET AND USB CONTROLLERS AND XYZ TOUCH PLATE!
CHECK OUT OUR NEWLY DESIGNED ETHERNET AND USB CONTROLLERS AND XYZ TOUCH PLATE!
Signed in as:
filler@godaddy.com
What comes in the G3 CNC Ethernet Controller Unit?
Custom Nema 4 IP 66/67 ABS plastic enclosure 16"X20"x6 1/2"
UCCNC AXBB-E Ethernet motion controller board (Y&A axis are software slaved)
Operates with Mach 3,4 or UCNC software (control software not included)!
Standard controller and driver settings for 1/2"-10 5 start lead screws
4 DM556 3rd generation 32 bit DSP fully digital micro stepper motor drivers
4 prewired Nema 23 425 oz/in stepper motors w/8mm shaft
1- 48v 10A adjustable power supply
1-24v/5v dual rail adjustable power supply
2- 110v input/output plugs and 2 solid state relays for accessory connections built in
2 80mm industrial grade 60CFM fans, 1-cooling and 1-exhaust
2 80mm black filter screens w/built in grill
1- C14 switch lighted power receptacle
1 power cord 6'
4 4 pin GX16 aviation connectors for stepper motors
3 2 pin GX16 aviation connectors for inputs and laser
1 4 pin GX16 aviation connector for spindle control
3 3 pin GX16 aviation connector for limit/homing proximity sensors
What comes with the G3 CNC USB Controller?
Custom Nema 4 IP 66/67 ABS plastic enclosure 16"X20"x6 1/2"
UCCNC UC100 USB motion controller board (Y&A axis are software slaved)
Operates with Mach 3,4 or UCCNC software (control software not included)!
CNC4PC C11G breakout board with usb cable
4 DM556 3rd generation 32 bit DSP fully digital micro stepper motor drivers
4 prewired Nema 23 425 oz/in stepper motors w/8mm shaft
1- 48v 10A adjustable power supply
1-24v/5v dual rail adjustable power supply
2- 110v input/output plugs and 2 solid state relays for accessory connections built in
2 80mm industrial grade 60CFM fans, 1-cooling and 1-exhaust
2 80mm black filter screens w/built in grill
1- C14 switch lighted power receptacle
1 power cord 6'
4 4 pin GX16 aviation connectors for stepper motors
3 2 pin GX16 aviation connectors for inputs and laser
1 4 pin GX16 aviation connector for spindle control
3 3 pin GX16 aviation connector for limit/homing proximity sensors
These are NPN inductive proximity sensors that are 12mm (1/2") in diameter. They have a detection range of 4-6mm to steel. Each sensor has an LED light to quickly indicate detection, and features an M12 x 1 threaded body that provides fine adjustment of detection distance for precision homing and limit function.
You receive 5 sensors, 2 for the Y axis, 2 for the X axis, and 1 for the Z axis. Also included are 3 position terminal blocks with covers for secure connections along with 15' of 22awg shielded cable for each axis. Mounting instructions are included.
The G3CNC XYZ corner finding touch plate allows for quick and exact setting of your tool height and work piece corner/edge location.
Just position the touch plate on top of your material at the corner, connect the magnet to your spindle collet, and use the Auto Z Touch Plate function in Mach 3/4. The Z axis will slowly move in the X direction until the bit makes contact with the plate. Next the Z axis will move in the Y direction until the bit contacts the plate. Finally the Z axis will climb above the plate then slowly move down until the bit makes contact with the touch plate. The system will automatically set the Z height and location to that of your work piece. The auto Z script for Mach is included. The touch plate is reversible for Z height only touch offs. Flip the plate over to use the side without the corner finding function.
The plate is made from grade 6061 aluminum and is precision machined to a 2 3/4" x 2 3/4" square. The plate thickness is .47" thick and the perimeter is .563" thick. The signal wire is secured to the plate in one of two locations with a 90 degree banana pin. The two connector points insures that the signal wire will not interfere with the auto zero Z axis movement process.
The G3CNC Manual spindle controller was designed to bypass your controller and connect directly to your spindle's VFD. This allows you to adjust your spindle speed at the table while your cnc is running without pausing and stopping your machine. This unit comes with setup instructions.
The unit is in a compact 4"x4"x 2" PVC waterproof box. it comes with 1 8' 18ga shielded 2 wire cable and 1 8' 18ga shielded 3 wire cable. Once you make the setting changes to the VFD and wire the unit up, simply power on your VFD and turn the unit on and you have the spindle speed control with the rotary switch. Setup instructions are included!
See the G3 CNC controller running a program in Mach 3.
See how quite and smooth our drivers and motor are.
Dave Gatton of Gatton CNC reviews the G3 CNC controller unit.
Copyright © 2020 G3 CNC - All Rights Reserved.
Contact us g3cnc@yahoo.com
Powered by GoDaddy Website Builder
Please see our new USB controller featuring the UCCNC UC100 controller and C11G breakout board!